Thursday, July 17, 2014

Upcycled Rug

My daughter recently repainted her room and her purple area rug no longer went with the new look. Instead of tossing a perfectly good rug that had no wear I decided to try to change the color with dye. This rug was perfect for dying - cotton rug with no rubber backing. I had seen pictures at The Rit Studio of dyers using Rit Color Remover to take the color out of clothing before dying. Normally I wouldn't have bothered. Going from purple to navy blue isn't that far of a stretch color wise but I wanted to see if this Color Remover would work.

Since you always start with clean, wet fabric step one was to wash the rug. Then it was time to use Rit Color Remover. While the rug was still dry I had tried to weigh it but my digital scale was being stupid. Four boxes seemed like a good number to start with. I tried to use the Color Remover in my front loaded but something went wrong. Probably user error. My washer emptied most of the Color Remover before the cycle started.

Well that's not right.
I rinsed the rug and then washed it again to get what remover there was out. The next morning I went back to the craft store for 4 more boxes of Color Remover. I was working under a deadline. Hubby was turning off the water when he got home from work to finish a plumbing project. This time I used my trusty utility sink in the laundry room. I dumped the 4 packets in the tub with lots of hot water and stirred. Then I added the wet rug. I swished it around off and on for about 30 minutes.

That's more like it.
There was no real way for me to wring out the rug so I just tossed it in the washer and turned on a rinse cycle. Then washed the rug with soap to get the remover out. I washed out the utility sink. Then filled it up with 4 bottles of Navy Blue Rit Dye and about 3 cups of salt. Added the wet rug and swished again for about 30 minutes.

The dye bath looked a little purple-ish but I wasn't worried.
I drained the utility tub out and filled up back up with plain water and let the rug soak while Hubby did his plumbing thing. One hour later he had the water back on and I could continue. I threw the rug into the washer to rinse the dye off. Then again with soap to get all the extra dye out. Usually I hang the rug over the back fence to dry but we were having heavy thunderstorms that night. Three dryer cycles later it was finally dry.

Looks great.

Before and After

Important Note - Make sure your gloves are longer than the dye bath is deep.

Hey look! I'm a Smurf.

Friday, June 27, 2014

Graphic 45 By the Sea Bird House

A few weeks ago for Mother's Day I made a Treasure Box for my Mom using Grapic 45 By the Sea paper collection. I wanted to make a companion piece for my Dad for Father's Day. That was my whole plan which wasn't much. Since I was winging it, I didn't take pictures. So sorry no step by step tutorial.

I went to Jo-Ann's and bought a birdhouse that kind of had a light house look to it and flat sides to decorate. First I painted two coats of Folk Art Chalky paint in Antique Mustard. Next I Mod Podged paper on the sides. Adding the paper on the front of the bird house was a little tricky to work out. With the hole and the peg it was difficult to line up the paper right. I fooled around with a few pieces of plain scrap paper but couldn't get it just right. I tried using hole punches but nothing would line up right. I was getting really frustrated. Finally one night in bed (I usually do my best thinking when I'm suppose to be sleeping) I realized if I cut the paper in half vertically I could line up everything better. Phew! It still took a few tries but eventually I got it all lined up, mostly.

Look close, you can't tell that the paper was cut in half. I save every scrap of this paper. It's so beautiful I don't want to waste any plus you just never know what you may be inspired to use. Using scraps from the side pieces I cut angle pieces and used the reverse side around the base of the house. Some jute twine around the peg hides the fact that I didn't cut the circle exact. I hot glued a few shells from a walk on the beach last summer.

At first I had painted the entire house yellow but decided to change the roof to Americana Williamsburg Blue that almost matches the paper. I hated to cut a whole sheet for the roof but really liked the little anchors. Some jute twine wrapped around the top along with a few sea shells.

Here are both pieces together. I love how they complement each other and my parents home.

Friday, June 20, 2014

Summer "Wreath" Tutorial

I love having seasonal decorations around the house. While Christmas & Halloween are big in our home, I also like to change things up in between Spring & Summer. As much as I love my Spring Wreath I wanted to do something a little different for Summer. After playing around on Pinterest for awhile I decided to walk around my favorite craft store, Jo-Ann's to get more inspiration.

I found this awesome frame-thingy. It reminded me of screen door.

I decided on lilac chalky paint for the color. First step was to tape off around the chalk board. I painted two coats on each side. I have to say it would have been easier to paint if I could have popped the chicken wire out. Instead I used a small detail brush and took my time.

I knew I wanted seed packets to attach to the screen. I couldn't find the look I was hoping for at my local home improvement center. A quick google search under "antique seed packets" got me there. I printed them on regular computer paper from my inkjet printer, nothing fancy here. The size for each is roughly size 4" by 6". Using some thin, scrap, cardboard I inked the edges to give them a finished look. Using Mod Podge I attached the "seed packets" to the card stock. After letting them dry for an hour or so, I sealed them with more Mod Podge on top.

 The cloths pin was "stained" with some Rit Dye I happen to have.

I knew I wanted flowers but had a hard time finding a flat pot or container. After searching my craft room for something else I could use, I stumbled upon my stash of plastic containers. I save these cause you just never know when you might need to store paint, sand, mod podge, glitter or whatever.

Once the container was cut in half length ways, I used craft glue to attach a sturdy piece of scrap cardboard to the back.

Using hot glue I carefully covered the container in jute twine. I just used a little glue to hold the twine in place. Of course it was once this was done was when I am I going to attach this to the screen. I carefully made 4 holes through the back of the container and fished craft wire through the container and in between the twine. I cut a small piece of floral foam and added some silk roses I had from another project.

Once I tried to attached the container to the screen I realized the wire wasn't going to be sturdy enough. As you can see I wrapped a small piece of jute twine around the container and tied it tightly in the back.

I had purchased children's garden gloves and garden tools to attach to the screen too. However, they were too heavy and I couldn't get them attached to the screen the way I liked.

I really like the chalk board at the top. It will be perfect to leave messages for our guests when we are in the back yard.

Friday, June 13, 2014

Graphic 45 By the Sea Treasure Box

When Graphic 45 came out with By the Sea paper collection, I fell in love. I knew I wanted to make something for my parents using this beautiful collection. Ten years ago my parents retired to a small barrier island in New Jersey called Brigantine. I thought By the Sea would fit in perfectly with their decor. I chose to make a small treasure box for my Mom for Mother's Day.

Graphic 45 papers are not available at major craft stores. I found a collection of By the Sea tags at a small scrapbooking store near Lancaster, PA. I ordered the papers from At Joann's I found a cute set of boxes and picked the middle size for this project. The other two are going into my craft stash for a future project.

Like most of my projects I didn't have a clear plan. I decided not to paint the box and just to use the plain brown paper as a background. I used matte Mod Podge to adhere the paper to the box and lid.

The nice thing about Graphic 45 is that their papers are two-sided. So for the inside of the lid I used one side of the papers for the lid and the other for the sides.

For the inside of the box itself I used the same paper as the inside of the lid and added a tag in the corner. I also "fussy" cut a seashell out. "Fussy" cut means to target a specific area on a paper or fabric and cut out just that area. I had cut the bottom paper a little too small so I edged around with some jute twine that I had with hot glue.

Back to the lid - I cut the paper to show this cool fish. I also used the other side of the paper (not shown here) to the edges of the lid box. I gently coated the lid with Mod Podge to seal the paper and to protect the surface. While it was drying I made a tag with some navy blue scrap paper I had and a seashell I had collected in Brigantine. More "fussy" cutting and twine finish off the tag. The tag itself and the individual pieces were also Mod Podged for protection. To attach the tag I used a few glue dots. Glue dots are one of the best inventions around.

For the outside of the box I used the same paper as the lid and Mod Podged it down. I added a tag and some more seashells. Using Mod Podge I used craft sand the same way you would add glitter to a project.

This was my first time using Graphic 45 papers and I was pleasantly surprised with the quality and weight of their papers. I very happy with the way this projected turned out. My Mom loved her gift.

I have plenty of paper left. I am currently working on something for my Dad for Father's Day.

Thursday, May 29, 2014

Rit Dye Studio T-shirt

Rit recently asked for crafters to join their Rit Studio. The first 500 people to sign up got a t-shirt. I was lucky enough to be one of those people. When I received the t-shirt I just set it aside not sure what I was going to do with it. Then I got an email asking to participate in a contest. "Dyesign" the t-shirt to win some great prizes. I dug out the t-shirt and washed it (the cats had been using it for nap time). As usual I had no plan put just got started.

After washing it, I started with the usual Elmer's Gel Glue as a relief and followed some flowers I printed off google. I wrote a blog post explaining this in detail - Rit Dyed T-shirt with Resist.

I more or less ignored the shaded areas. But once I got to the flowers on the end I decided to color the entire flower in thinking I could make different color flowers. I also rubber banded a section at the bottom for a burst effect. Once the glue dried I dyed the shirt in fuchsia for about an hour. Rinsed the entire shirt to get the glue and dye out and let dry.

Well that wasn't exactly what I was going for. You really couldn't see the outline of any of the flowers. But I kept plugging along. I wet the t-shirt and "sponged" sunshine orange dye shirt with an old rag.

I let that sit for about a day or so. Actually I got busy and forgot about the project. Rinsed again and let dry.

Now to try to come up with a plan...I know fabric markers. I grabbed a black fabric marker and put the flower page back under the t-shirt and wet the t-shirt so I could see the flowers underneath and traced them. Of course I did not read the directions on the side of the marker. As I traced the marker started to run. Oh well I figured I'm just going to dye it again.

I didn't wait for the marker to dry. I just dyed the entire shirt in fuchsia again. Then rubber banded some more bursts and dyed it in sunshine orange, I think. I really don't remember the exact order of colors or for how long. I was "winging" it with this project for about a week and a half and didn't keep exact notes. I had 3 bottles of dye sitting out - fuchsia, sunshine orange, and tangerine so at some point I probably used all of them. I know some where in there I washed the shirt at least twice to make sure all the dye was out and so I could see how it was looking.

At some point I did read the directions for the marker and once the shirt was dry I retraced the flowers based on what did survive the first time. I let the marker dry for 24 hours before I did any more dying.

The marker isn't as pale as it looks in this picture.

The burst at the bottom of the shirt came out so well. I'm really happy about it.

I had no plans for the back of the shirt. All that cool marbling just kind of appeared. I love when that happens.

Overall I am very happy with the shirt. I can't wait to wear it and show it off. I will post an update on here if I win. Wish me luck.

UPDATE - I am a winner! I won the Most Fashionable Category. Yea Me!

Friday, May 23, 2014

Decorate Your iPhone Charger

Phone chargers are a part of our everyday life so why should we shouldn't we brighten them up a bit.

This is a quick and easy project. All you need is Mod Podge, Washi Tape, glitter, and of course your charger. Mod Podge is glue and sealant all in one. Washi Tape is a slightly sticky decorative tape.

To decorate your charger with glitter the first step is to coat the charger with Mod Podge.

Cover the charger with glitter. Working over a file folder or scrap paper will allow you to pour the excess glitter back into the jar.

If any Mod Podge or glitter is anywhere you do not want it to be, just wipe off with a damp towel.

Allow the charger to dry for about an hour. Using a plastic lid as a drying surface is a good idea so the charger won't stick.

Add a top coat of Mod Podge to seal the glitter. I have a special jar of Mod Podge just for glitter since I usually double dip my brush. You can wipe your brush off after each stroke so no glitter gets into your Mod Podge.

Let the charger dry for several hours or overnight.

To decorate with Washi Tape wrap the tape around the charger and cover with Mod Podge. Let dry several hours or over night.

Friday, May 16, 2014

Rit Dyed T-shirt with Resist

I found a really fun project on Pinterest. There are several tutorials out there. Here is my take on dying t-shirts with Rit Dye and using Elmer's Gel Glue as the resist.

The great thing about this project is that you can use anything for the design.

Start with a plain white t-shirt. Craft stores have good quality t-shirts for cheap. I purchased mine at Jo-Ann's when they had a sale - 4 shirts for $10. I also picked up Rit Dye and Elmer's Gel Glue while I was there. You need to use Elmer's Gel glue for this project. Regular white glue won't work.

The first step is to wash your shirts. I also dried them to make sure no shrinkage occured.

For the images I picked a softball for my sporty daughter and a mandala flower for my artsy daughter. Simply designs work best so in the Google search I added "coloring pages". This gives you a nice crisp design to work with. Print your picture out in the size you want. I printed full size (8 1/2 by 11) for each shirt. For a small child you might want to go a little smaller.

First step is to wet the t-shirt. Since you are working with wet clothes and dye make sure your work area is water proof. You can lay a trash bag flat on your surface to protect it.

I put the picture in one of those clear protective sleeves for binders. This will protect the paper and make sure the glue does not go through to the back of the shirt. Slide the picture inside the sleeve in between the front and back of the shirt. Center it to where you would like the design.

Get out your Elmer's Gel Glue and trace the design.

Let the glue dry for several hours or overnight.

Now to get your dye bath ready. I used an old glass pot in the utility sink in our basement. If you have a large metal pot, that would work also. Remember you are using dye so protect your area. Fill your pot with cold water and add the dye. How much dye you use depends on how dark or light you want the color to be. Carefully take the plastic sleeve out from between the shirt and add your shirt to the dye bath. How long you keep it in the dye bath will also determine the color. I kept each shirt in the bath for about an hour, stirring occasionally.

I also covered the pot because with 3 kitties these are the lessons you learn.

After the hour is up DO NOT rinse the shirt just hang it up to dry. If you do not have a safe place to do this, then lay it flat again on the surface you prepared earlier.

I hung the shirts over our utility sink making sure it would drip dry right into the sink.

Since I am working with two different colors for two different shirts I just repeated the process for the second shirt making sure to rinse the pot very well.

Once both shirts hanging to dry I made sure they were not touching so no colors would bleed on to each other.

Here is a close up of each shirt.

Here are some shirts I made last summer. The lesson I learnt the first time was to use PLASTIC hangers. I used metal hangers the first time and there are a few rust stains on the back of the shirts.